net-dialup/ueagle4-atm: Remove last-rited pkg

Closes: https://bugs.gentoo.org/661884
Signed-off-by: Michał Górny <mgorny@gentoo.org>

4 files changed, 0 insertions, 299 deletions

diff --git a/net-dialup/ueagle4-atm/Manifest b/net-dialup/ueagle4-atm/Manifest
deleted file mode 100644
index 5f00994926e4..000000000000
--- a/net-dialup/ueagle4-atm/Manifest
+++ /dev/null
@@ -1 +0,0 @@
-DIST ueagle4-data-1.0.tar.gz 217512 BLAKE2B 3714bcb268e5a9e7d504e1eb618cf23a441b3a19ef675eeb2cf10f8a6979ebaa5896de7101572206a6f9e5ee9764329ce2cd180d456bb869e58f39f2326110ac SHA512 3d47150eb288865432e7201390669262e0d12239f5d45d194da8abe535e69cabcb53ef6b8757ab7e3c495394ecd74b781ac724635918b70c479a1219b3bcaa74
diff --git a/net-dialup/ueagle4-atm/files/README b/net-dialup/ueagle4-atm/files/README
deleted file mode 100644
index 20067824f303..000000000000
--- a/net-dialup/ueagle4-atm/files/README
+++ /dev/null
@@ -1,235 +0,0 @@
-Introduction
-============
-
-This ebuild installs firmware files necessary for Eagle USB E4 ADSL 
-Modem driver which first appeared in kernel 2.6.16.
-
-Configuration
-=============
-
-Most ADSL modems are connected via the ATM protocol, rather
-than Ethernet. For ATM, run the following:
-   euse -E atm && emerge net-dialup/ppp net-dialup/ueagle-atm
-
-It is necessary to choose an interface number for the connection. This
-is arbitrary - the only requirement is that the connection number is
-not already in use. The first available number is 0, and it is usual to
-choose the lowest unused number. For the purposes of this document, 0
-will be chosen.
-
-Add the following lines from the appropriate section below to
-/etc/conf.d/net, then customize them as per the inline comments.
-
-
-a) PPPoATM configuration:
-
-config_ppp0='ppp'  # Runs /lib/rcscripts/net/pppd.sh
-# The 2 numbers represent the VPI & VCI of your ISP, and they are separated
-# by a dot. Ask your ISP about those numbers.
-link_ppp0='0.38'
-plugins_ppp0='pppoa' 
-# 'man pppd' shows other options. Compression is disabled because it is
-# rarely taken advantage of, and may interfere with the connection.
-# Add option 'usepeerdns' to populate /etc/resolv.conf
-pppd_ppp0='updetach noauth debug defaultroute noaccomp nobsdcomp noccp
-	nodeflate nopcomp novj novjccomp child-timeout 60'
-username_ppp0='username@isp.com'  # ADSL login, assigned by your ISP
-password_ppp0='password'  # ADSL password, assigned by your ISP
-
-# If the kernel modules are not built-in, then they must be loaded
-# before starting the PPP daemon:
-function preup() {
-	if [[ "$1" = "ppp0" ]] ; then
-		modprobe -q ueagle-atm
-		return 0
-	fi
-}
-
-
-b) PPPoE configuration:
-
-# Configure first the RFC2684 bridge interface 
-config_nas0='null'
-# Use "-e 0" for LLC mux or "-e 1" for VC mux.
-# The 2 numbers after "-a" represent the VPI & VCI of your ISP, and
-# they are separated by a dot. Ask your ISP about those numbers.
-br2684ctl_nas0='-e 0 -a 0.38'
-
-config_ppp0='ppp'  # Runs /lib/rcscripts/net/pppd.sh
-link_ppp0='nas0' # The name of the RFC2684 bridge interface
-plugins_ppp0='pppoe'
-# 'man pppd' shows other options. Compression is disabled because it is
-# rarely taken advantage of, and may interfere with the connection.
-# Add option 'usepeerdns' to populate /etc/resolv.conf
-pppd_ppp0='updetach noauth debug defaultroute noaccomp nobsdcomp noccp
-	nodeflate nopcomp novj novjccomp child-timeout 60'
-username_ppp0='username@isp.com'  # ADSL login, assigned by your ISP
-password_ppp0='password'  # ADSL password, assigned by your ISP
-
-depend_ppp0() {
-    need net.nas0
-}
-
-# If the kernel modules are not built-in, then they must be loaded
-# before starting the RFC2684 bridge:
-function preup() {
-	if [[ "$1" = "nas0" ]] ; then
-		modprobe -q ueagle-atm
-		return 0
-	fi
-}
-
-
-Configuration continued
-=======================
-
-Create a symlink for the new network interface, for it to be enabled by
-baselayout:
-  cd /etc/init.d && ln -sfn net.lo net.ppp0
-If you use PPPoE, you should also create the symlink for the RFC2684
-bridge interface:
-  cd /etc/init.d && ln -sfn net.lo net.nas0
-
-The "debug" option adds some extra commentary from pppd regarding the
-connection to /var/log/messages, e.g.:
-"sent [LCP ConfReq id=0x1 <magic 0x7bea6ef1>]". It is wise to keep the
-option on permanently, due to its usefulness when debugging.
-
-Set RC_NET_STRICT_CHECKING="yes" in /etc/conf.d/rc, to prevent Internet
-services in /etc/init.d/ from starting before the Internet connection
-is established. Other options are to start/stop programs in
-/etc/ppp/ip-{up,down}.local, and to customize initscript dependencies
-as described in:
-  http://www.gentoo.org/doc/en/handbook/handbook-x86.xml?part=2&chap=4
-
-
-Starting the Connection
-=======================
-
-To start manually, with the modem connected:
-  /etc/init.d/net.ppp0 start
-
-To start automatically when the PC boots:
-  rc-update add net.ppp0 default
-
-
-Kernel Configuration
-====================
-
-The ebuild, during an emerge, checks that the required kernel modules
-are present.
-
-Note that in the list below, "[*]" means that the option is compiled
-into the kernel, whereas "[M]" means that the option can either be
-compiled into the kernel, or as a module. Compiling them into the
-kernel is recommended, to guarantee that the modules are already loaded
-when they are needed, and it will improve the bootup time by a couple
-of seconds.
-
-In "make menuconfig", you can press "/" and search on e.g. "eagle"
-to see exactly where an option is - the location of an option and its
-dependencies can change between kernel versions.
-
-Check that the following kernel options are configured as shown (this
-list includes the prerequisites, e.g. USB_UEAGLEATM depends on USB):
-
- Code maturity level options  --->
-  [*] Prompt for development and/or incomplete code/drivers
-        - CONFIG_EXPERIMENTAL
-
- Device Drivers  --->
-  Generic Driver Options  --->
-   [ ] Select only drivers that don't need compile-time external
-        firmware (*unselected*) - CONFIG_STANDALONE
-   [*] Hotplug firmware loading support - CONFIG_FW_LOADER
-
- Networking  --->
-   [*] Networking support - CONFIG_NET
-   Networking options  --->
-    [*] Packet socket - CONFIG_PACKET
-    [M] Asynchronous Transfer Mode (ATM) - CONFIG_ATM
-    [M] RFC1483/2684 Bridged protocols - CONFIG_ATM_BR2684 (only needed for PPPoE)
-   
- Device Drivers  --->
-  Network device support  --->
-   [*] Network device support - CONFIG_NETDEVICES
-   [*] PPP (point-to-point protocol) support - CONFIG_PPP
-   [M] PPP Deflate compression - CONFIG_PPP_DEFLATE (only useful if
-        compression is supported - rare)
-   [M] PPP BSD-Compress compression - CONFIG_PPP_BSDCOMP (only useful
-        if compression is supported - rare)
-   [M] PPP over Ethernet - CONFIG_PPPOE (only needed for PPPoE)
-   [M] PPP over ATM - CONFIG_PPPOATM (only needed for PPPoATM)
-  USB support  --->
-   [*] Support for Host-side USB - CONFIG_USB
-   [*] USB device filesystem - CONFIG_USB_DEVICEFS
-   [M] (O or U)HCI HCD support
-   USB DSL modem support  ---> 
-    [M] USB DSL modem support - CONFIG_USB_ATM
-    [M] ADI 930 and eagle USB DSL modem - CONFIG_USB_UEAGLEATM
-
-
-
-Troubleshooting
-===============
-
-Try "emerge ueagle-atm" again, because the ebuild checks that the
-required kernel modules are present (showing a warning message if
-appropriate), and creates the firmware files in /lib/firmware/ueagle-atm.
-
-If the modem is unresponsive, then run "/etc/init.d/net.ppp0 stop" and
-unplug the modem for 30 seconds, to drain its memory. Then reconnect
-the modem to the PC and run "/etc/init.d/net.ppp0 start"
-
-To check the modem's connection progress, run:
-  tail -f /var/log/messages
-/var/log/messages should show e.g.:
-
-pppd[nnn]: Plugin pppoatm.so loaded.
-pppd[nnn]: pppd n.n.n started by root, uid 0
-pppd[nnn]: Using interface ppp0
-pppd[nnn]: Connect: ppp0 <--> n.nn
-ADSL line is synchronising
-DSL line goes up
-ADSL line is up (nnn Kib/s down | nnn Kib/s up)
-pppd[nnn]: CHAP authentication succeeded
-pppd[nnn]: local  IP address nnn.nnn.nnn.nnn
-pppd[nnn]: remote IP address nnn.nnn.nnn.nnn
-
-
-If the authentification fails, then check username_ppp0 and
-password_ppp0.
-
-If the ADSL connection is not established, then check the options in
-pppd_ppp0. "man pppd" explains all the options in that file.
-
-If the ADSL connection seems to have worked, but no websites can be
-contacted, then check that /etc/resolv.conf is populated, and possibly
-add the "usepeerdns" option (to use the ISP's DNS) to pppd_ppp0 in
-/etc/conf.d/net .
-
-If the problem is still not resolved, post to the Gentoo Forums at 
-http://forums.gentoo.org/ and ultimately, if there is no answer, 
-file a bug at http://bugs.gentoo.org/ .
-
-
-Compression
-===========
-
-Some ISPs require compression to be disabled in order for the
-connection to work, so the default configuration described above
-disables compression. Few ISPs support ADSL compression anyway. If you
-are lucky enough to have an ISP which *does* support compression
-(Google is your best friend for determining this), then compression can
-be enabled by following these steps:
-
-* Compile the kernel modules CONFIG_PPP_DEFLATE and CONFIG_PPP_BSDCOMP
-(only one is strictly necessary - pppd prefers "deflate" compression).
-Add them to /etc/modules.autoload.d/kernel-2.6 or /etc/conf.d/net above
-the "pppoatm" line, if they are not built-in.
-* Remove the following options in pppd_ppp0:
-  noaccomp nobsdcomp noccp nodeflate nopcomp novj novjccomp
-* Ensure that "debug" is in the pppd_ppp0 options, to check that
-compression is being utilized. Note that "module registered" in
-/var/log/messages only confirms that the kernel module is loaded - 
-it does not indicate that the connection is compressed.
diff --git a/net-dialup/ueagle4-atm/metadata.xml b/net-dialup/ueagle4-atm/metadata.xml
deleted file mode 100644
index 331b50f53b69..000000000000
--- a/net-dialup/ueagle4-atm/metadata.xml
+++ /dev/null
@@ -1,7 +0,0 @@
-<?xml version="1.0" encoding="UTF-8"?>
-<!DOCTYPE pkgmetadata SYSTEM "http://www.gentoo.org/dtd/metadata.dtd">
-<pkgmetadata>
-	<!-- maintainer-needed -->
-	<longdescription>Firmware and configuration instructions for Eagle USB E4 ADSL Modem driver
-available in kernels &gt;= 2.6.16.</longdescription>
-</pkgmetadata>
diff --git a/net-dialup/ueagle4-atm/ueagle4-atm-1.0.ebuild b/net-dialup/ueagle4-atm/ueagle4-atm-1.0.ebuild
deleted file mode 100644
index 80b2ba00625b..000000000000
--- a/net-dialup/ueagle4-atm/ueagle4-atm-1.0.ebuild
+++ /dev/null
@@ -1,56 +0,0 @@
-# Copyright 1999-2017 Gentoo Foundation
-# Distributed under the terms of the GNU General Public License v2
-
-EAPI=6
-
-inherit eutils linux-info
-
-DESCRIPTION="Firmware and configuration instructions for Eagle USB E4 ADSL Modem driver"
-HOMEPAGE="https://gna.org/projects/ueagleatm/"
-SRC_URI="http://eagle-usb.org/ueagle-atm/non-free/ueagle4-data-${PV}.tar.gz"
-
-LICENSE="Ikanos"
-SLOT="0"
-KEYWORDS="~amd64 ~x86"
-
-DEPEND=""
-RDEPEND="net-dialup/ppp
-	!sys-kernel/linux-firmware"
-
-S="${WORKDIR}/ueagle4-data-${PV}"
-
-src_install() {
-	# Copy to the firmware directory
-	insinto /lib/firmware/ueagle-atm
-	doins *
-
-	# Documentation necessary to complete the setup
-	dodoc "${FILESDIR}/README"
-}
-
-pkg_postinst() {
-	# Check kernel configuration
-	local CONFIG_CHECK="~FW_LOADER ~NET ~PACKET ~ATM ~NETDEVICES ~USB_DEVICEFS ~USB_ATM ~USB_UEAGLEATM \
-		~PPP ~PPPOATM ~PPPOE ~ATM_BR2684"
-	local WARNING_PPPOATM="CONFIG_PPPOATM:\t is not set (required for PPPoA links)"
-	local WARNING_PPPOE="CONFIG_PPPOE:\t is not set (required for PPPoE links)"
-	local WARNING_ATM_BR2684="CONFIG_ATM_BR2684:\t is not set (required for PPPoE links)"
-	check_extra_config
-	echo
-
-	# Check user-space for PPPoA support
-	if ! has_version net-dialup/ppp[atm] ; then
-		ewarn "Run the following command if connecting via PPPoA protocol:"
-		ewarn "   euse -E atm && emerge net-dialup/ppp"
-		echo
-	fi
-	# Check user-space for PPPoE support
-	if ! has_version net-dialup/linux-atm ; then
-		ewarn "Run the following command if connecting via PPPoE protocol:"
-		ewarn "   emerge net-dialup/linux-atm"
-		echo
-	fi
-
-	ewarn "To complete the installation, you must read the documentation in"
-	ewarn "   ${ROOT}usr/share/doc/${PF}"
-}